$29.99
Open-Box Omigo Element+
Non-Electric Warm Water Bidet Attachment
Once you experience a bidet with warm water, there’s no going back. Ours comes with fully adjustable water temperature and pressure and more. Or, if you just want a refreshing, ambient-temperature bidet—it can be that, too.
$39.99
(You save
$14.01
)
-
Not available for shipment to Canada
-
Ships for free to contiguous US and Canada
Get attached to warm water washes.
Level up your hygiene and comfort by turning your toilet into a bidet. Omigo Element+ is electricity and battery-free and attaches easily underneath any toilet seat—without a plumber or additional parts. Like options? Element+ comes with all of the parts needed to wash with warm or cool water. Get the most out of your Element+ with adjustable water temperature, or only set it up for ambient temperature washes—the choice is yours. Either way, you’ll get 2 retractable nozzles for front and rear washes and intuitive side-arm controls with temperature adjustment. That’s good for your hygiene, and the planet’s too, by helping you use less toilet paper.
-
hygienic, retractable nozzles
-
adjustable water pressure
-
a sustainable solution for your bathroom
-
designed for easy installation
Item #CBHA
Full Features
The right wash for every body
- warm and cool water bidet washes
- fully adjustable water temperature and pressure
- side-arm control with large, easy-turn dials
- can be used as an ambient-temperature bidet
Features you'll love
- delivers a clean, hygienic wash
- fits round and elongated toilets
- ceramic core internal valve
- separate front and rear nozzles
- self-rinsing system runs fresh water over both nozzles before and after each use
- nozzles retract behind guard to stay clean between uses
Simple, DIY installation
- slim frame installs under your existing seat
- everything included for standard install
- connects to your sink's hot water supply
- installs under your existing seat
Sustainability in your bathroom
- a sustainable alternative to toilet paper and flushable wipes
- powered by water pressure alone, no batteries or electricity required
Element+ FAQs.
How does Element+ connect to warm water?
In order to get warm water washes, you will need access to your sink's warm water supply. We provide the necessary connections and attachments for a simple installation.
Is the water Element+ uses clean?
Yes! It is the same clean water used for your sink and shower. Fresh water is accessed using a T-Valve that brings it directly to your Element+ for a perfectly fresh wash.
Will this fit my toilet?
Element is designed to fit most US toilets, both round and elongated, including most one-piece and curved toilet fixtures.
To be sure, measure the distance between the bolt holes. The space must be between 5¼ inches and 8 inches.
Then measure the distance from the center of the bolt holes to the toilet tank to ensure proper clearance. There must be at least ¾ inch of clearance.
If you meet those measurement requirements then you're good to go!
Do I need an outlet to use Element+?
Nope! No electrical outlet required. Element+ is mechanically powered, using the water pressure in your pipes to operate. Even low water pressure homes can use Element+.
How do I dry off?
After you're done washing, simply pat dry with a few squares of toilet paper to finish the job.
Do I need an outlet to use Element+?
Nope! No electrical outlet required. Element+ is mechanically powered, using the water pressure in your pipes to operate. Even low water pressure homes can use Element+.
Do the nozzles “get in the way”?
Element+'s nozzles are retracted and covered so you won't contaminate them when not in use. Plus, we built in a self-cleaning system so the nozzles are rinsed before each use.
How far does the arm stick out from the toilet?
The control arm extends out to the right side of the toilet approximately 4 inches. This can vary depending on your toilet since the brackets are adjustable, but 4 inches is average.
How can I clean my bidet?
All of our bidets can be cleaned with a soft cloth and standard mild cleaning detergents. Since Element+ is so easy to install, it's easy to completely remove if you ever want to deep clean your toilet.
Do you make a left-handed Element+?
No, we do not offer a left-handed product at this time.
Installation so easy, anyone can do it.
Element comes with all the parts and hardware for a standard installation
Step 1: Prep your toilet.
- remove the bidet toilet seat and clean the bowl
- shut off the water valve and flush the toilet
- detach the metal hose from toilet tank fill valve
Step 2: Connect the fresh water supply.
- screw the T-Valve onto the fill valve
- attach the metal hose to the bottom of the T-Valve
- attach the bidet hose to the middle of the T-Valve
Step 3: Install your Element+.
- center your bidet at the back of the bowl
- align the circular brackets to the bolt holes
Step 4: Attach the warm water line.
- turn off your sink’s warm water supply valve
- connect the hot water T-Valve to the warm water valve
- attach the warm water line to the T-Valve
Step 5: Final steps and checks.
- attach the clear warm water line and the metal bidet hose to the bidet
- turn on both water valves and check for leaks
- start washing!
Dimensions
Main Body: 13.46" (W) x 5.55" (D) x .25" (H)
Arm: 2.12" (W) x 6.79" (D) x 1.31" (H)
Arm: 2.12" (W) x 6.79" (D) x 1.31" (H)
Included Components
Stainless Steel 7⁄8" Cool Water T–Valve
Stainless Steel 3⁄8" Warm Water T–Valve
Durable Braided Metal Cool Water Hose
6' of High Temp Hot Water Tubing
All Necessary O–Rings and Plumbers Tape
Stainless Steel 3⁄8" Warm Water T–Valve
Durable Braided Metal Cool Water Hose
6' of High Temp Hot Water Tubing
All Necessary O–Rings and Plumbers Tape
Warranty
1-Year Limited Warranty
You May Also Like
$39.99 - $44.99
$59.99 - $64.99